Just How to Set up a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Just How to Set up a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
Everybody is bound to have their personal assumption with regards to How to Install a Bathtub.
Setting up a tub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bathtub with a new one is also a moderately challenging job. If the old tub is readily obtainable, the task can relocate rapidly; if you have to open a wall to get rid of the old bathtub as well as position the new bath tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will require an assistant to leave the old tub and embeded in the brand-new one. Ensure you have actually certified on your own for the job and also fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to think about employing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This post will assist you install a brand-new bathtub in your washroom if you have currently purchased a brand-new tub and also don't require to change the setup of your previous supply of water pipelines.
Your tools and also material list should make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the restricted access that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. When the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washers are in place between the tap and the sink. Safeguard the faucet in position with the maker supplied backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The former type should be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Making use of both wooden boards under its feet, place the bathtub in the called for setting. The wooden boards are helpful in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level reads degree.
To mount taps, fit the bottom of the outermost adaptable faucet connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Switch on the water supply and also inspect all joints as well as new pipework for leakages as well as tighten them if necessary. Load the tub and also examine the overflow outlet and the regular electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait till the tub has been made use of a minimum of when as this will certainly settle it right into its final placement.
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom ought to be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with wetness and also possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealer can split rather very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the market. It is recommended to fit the tiles using waterproof or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our excerpt about How to Install a Bathtub Yourself. Thank you so much for taking a few minutes to read through our post. Loved our piece? Please share it. Let someone else find it. Thanks a lot for your time. Please check our website back soon.
Phone
Report this page